Termék részletei

3-phase and single phase option are available (model dependent) in order to meet specific torque characteristics for the wide variety of applications that Q range actuators are suitable for.

At standard Q range:

• 3 phase; 1 phase motors by high starting output torque
• 3 pcs embedded thermostats for motor thermal protection inside the enclosure
• Toque and position switches for remote indication
• Mechanical position indicator on the top of actuator
• Optional CPT or potentiometer for continuous position indication

The Q Pak variant includes the addition of a control interface module, including a local control selectors, logic PCB, motor switchgear and transformer. This allows for increased integration of Q Pak actuators with existing site systems.

Inside the long cover:

• Local control selectors
• logic PCB board
• motor switchgear
• transformer - within the pack module

Phase rotation correction:

Syncrophase is included - it always translate the incoming phase to make rotation in the correct direction by energising the correct contactors.

Integral Controls:

Q-pak are models as ready-to-operate solutions

Only power supply is needed externally to make actuator working (by motorswitch gear + local PCB 

Remote mode by connecting the concerned terminals

Motor switch gear:

By a reversing contactor inside the actuator

Reversing contactor include time delay circuit for avoiding shock loads in case of switches.

Increased functionality:

FOL - analouge control makes possible intermediate positioning (control) and 

CPT - analouge feedback makes possible intermediate position feedback

BUS Control Systems:

By Pakscan FCU that can be connected to the Master station and so that the DCS. Control and feedback about:

• current position showing
• alarms feedback
• diagnostic 
• remote control and indication is possible

Types of FCU and network: Foundation Fieldbus, Profibus, DeviceNet, Modbus

Available sizes/ torques/ ISO-connection sizes:

Q100 - Output max.* torque- 135 Nm/ F05 - F07 (ISO 5211), or FA05 - FA07 (MSS SP-101)

Q300 - Output max. torque   - 406 Nm/ F07 - F10 (ISO 5211), or FA07 - FA10 (MSS SP-101) 

Q450 - Output max. torque   - 610 Nm/ F07 - F10 (ISO 5211), or FA07 - FA10 (MSS SP-101)  

Q650 - Output max. torque   - 900 Nm  - torque can be set between 30-100% to meet with the application 

- ISO connection sizes/ at  Q650: F12/ F14/ F16 (ISO 5211), or FA12/ FA14/ FA16 (MSS SP-101 ) 

Stroke times:

Q100 - 27/ 18/ 9 sec (50 Hz)

Q300 - 54/ 36/ 18 sec (50 Hz)  

Q450 - 54/ 36/ 18 sec (50 Hz)  

Q650 - 15/ 30/ 45 sec (50 Hz) 

Power Supply:

1 phase - 110 - 240 VAC/ 50 - 60 Hz 

3 phase - 380 - 480 VAC/ 50 - 60 Hz

at Q450 and Q650 sizes- are only available by 3 phase motor

Enclosure:

Watertight , IP68 (down to 3 metres depth for 48 hours)

Ambient temperature:

-30 .. +70 °C

Drive mechanism:

Self-locking drive train to avoid backdrives from valve direction

Drive train permanently immersed in oil bath to ensure to ensure max. efficiency

Drive nut can be taken out in order to machining for valve adaptation

Limit and torque switches:

Torque and auxiliary limit switches are cahngeover type (NO/ NC) contacts

By inductive load ratings: 110-240 VAC - 15 A/ 110 VDC - 0,25 A/ 50 VDC - 2,5 A/ 24 VDC - 3 A

Motor/ Classification/ Duty cycle/ Task:

3 phase- A & B Class- S2 - 20% - 60 start per hour - for on&off application

1 phase- A & B Class - S2 - 20% - 60 start per hour - for on&off application

Motor insulation:

F insulation class and integrated thermostat

Cable entries:

As standard: 2 x M32 vagy 2 x 1 NPT (imperial)

Optional - additional entry by size M20

Enclosure:

Drive and motor enclosure by die-cast aluminium 

Rest of the parts from aluminium alloy